(12)4 Way / 2 Position 1/4" NPT Manual and Mechanical Operators
Technical Data Port Sizes: 1/4 NPT Working Pressure: Vacuum service to 150 psi can be used for dual pressure applications. Flow: Cv = 1.1 Temperature Range: -20º to +175 ºF Media: Air (Lubricated or non-lubricated) Materials:
Body: Zinc die casting Spools: Stainless Steel
Features:
The 1/4" 4-way, 5-ported CD07 valve is an extremely versatile, yet compact design. This low profile spool type design will not only enhance the appearance of your equipment, but will save valuable engineering space.
A simplified internal design allows for consistently reliable performance and ease of operation.
(19)Operator Kits include all Operator Portions, Springs, Spacers, Plates, O-Rings, Mounting Screws & Angle Plates necessary in mounting the Operator Portion to the Main Valve Body.
PS2…Series valves use PS20000-…kits. PS3…Series valves use PS30000-…kits./ImgCustom/30/placeholder_notavailable.gif
The one piece valve cartridge replaces the individual valve parts assembly for the following devices:
"A" PILOTAIR Valves "H" CONTROLAIR Valves FLEXAIR Valves - Side Valve Cavity
Quick, positive repair and conversion can be accomplished by directly replacing the old individual parts with the new factory pressure tested cartridge. The cartridge valve simplifies repair and eliminates possible problems due to improper parts assembly. The modern engineered plastic and stainless steel construction provide superior corrosion resistance and sealing characteristics.
NOTE:
With the above kits, the elastomer seals and some common wear parts in the valve portions of the assemblies can be repaired. On severely worn or damaged valves, additional parts may be required.
The above kits do not contain any parts for the mechanical operating portions of the valves. The mechanical operating portions of the valve should be repaired when necessary, with individually selected parts, and tested before being put in service.
Refer to Service Bulletin SM-700.7400 for additional parts information and service instructions on the type "A" PILOTAIR pneumatic directional valves./Asset/a1442.jpg
(10)With these repair kits, the elastomer seals and some common wear parts on the component are renewed. On severely worn or damaged valves, additional parts may be required. For additional parts, information and service instructions, refer to Service Bulletin SM-300.30./ImgCustom/30/placeholder_notavailable.gif
(3)3 Position Subbase Mounted Spring-Centered Double Solenoid Operated, Closed Center
TECHNICAL DATA: Port Sizes: 1/4" & 3/8" NPTF Working Pressure:
Valve inlet: 200 psi (13.8 bar) maximum with external pilot 150 psi (10.3 bar) maximum with internal pilot
Minimum Pilot Pressure: 2 position: 15 psi (1 bar), Spring return models: 25 psi (1.7 bar) Flow: Cv 1.0 (1000 Nl/min) Temperature Range: -20ºF to +160ºF (-29ºC to 71ºC) Media: Air and inert gases (In service higher than 18 cycles per minute or with continuous air flow, a lubricator is recommended.) Materials:
Body, subplate and operators: Die cast anodized aluminum Spool: Machined from high-tensile anodized aluminum Seals: Buna-N specially treated
Manual Override: Non-Locking
Note: Other coil voltages are available - selection will be done at checkout./Asset/a1455.jpg
TECHNICAL DATA: Port Sizes: 1/4" & 3/8" NPTF Working Pressure:
Valve inlet: 200 psi (13.8 bar) maximum with external pilot 150 psi (10.3 bar) maximum with internal pilot
Minimum Pilot Pressure: 2 position: 15 psi (1 bar), Spring return models: 25 psi (1.7 bar) Flow: Cv 1.0 (1000 Nl/min) Temperature Range: -20ºF to +160ºF (-29ºC to 71ºC) Media: Air and inert gases (In service higher than 18 cycles per minute or with continuous air flow, a lubricator is recommended.) Materials:
Body, subplate and operators: Die cast anodized aluminum Spool: Machined from high-tensile anodized aluminum Seals: Buna-N specially treated
Manual Override: Non-Locking
Note: Other coil voltages are available - selection will be done at checkout./Asset/a1455.jpg
