| Items |
 R432015769 Sandwich Auxiliary Pressure Block |
R432015770 Sandwich Auxiliary Pressure Block |
R432015321 Blanking Plate Kit |
R432015323 Transition Plate Kit |
0821302050 Sandwich Pressure Regulator |
|||||
| Description |
The separate pressure block allows for more than two pressures to be provided to a manifold of valves. This unit sandwiches between the valve and base. Pressure to the balance of the manifold is isolated. Kit includes plate (1), gasket (1), screws (4). Allows 3 or more pressure to be applied to the same manifold assembly. |
The separate pressure block allows for more than two pressures to be provided to a manifold of valves. This unit sandwiches between the valve and base. Pressure to the balance of the manifold is isolated. Kit includes plate (1), gasket (1), screws (4). Allows 3 or more pressure to be applied to the same manifold assembly. |
Allows for valve to be added later. Can be removed to add valve to existing manifold. Kit includes plate (1), gasket (1), screws (4). Shown on 1/4" base |
For part no. R432015315 (old style) and R432015318 This kit allows the combining of our sizes I and II bases, with side porting, in the same manifold. No need to sacrifice by either undersizing or oversizing to meet design needs. Kit contains all hardware plus: 1 - Transition plate (Size I to Size II) 1 - Size I Endplate 1 - Size n Endplate (Cannot be used with R432015314) |
Ideal for applications within a manifold where a particular pressure is required for one or more valves. Our regulator controls inlet pressure through to each cylinder port. A relieving type, the knob will also lock into a given position. Kit includes regulator (1), gasket (1), screws (4), plus gauge for the 10-120 psi model. | |||||
| Old Part # | P -069685-00000 | P -069685-00001 | P -068440-00000 | P -068441-00001 | 0821302050 | |||||
| Height | 1.54 Inch39.1 mm | 1.54 Inch39.1 mm | 3.15 Inch80 mm | 2.64 Inch67 mm | ||||||
| Maximum Overall Length | 4.28 Inch108.7 mm | 4.28 Inch108.7 mm | ||||||||
| Width | 1.23 Inch31.2 mm | |||||||||
| Length | 4.97 Inch126.2 mm | 11.22 Inch285 mm | ||||||||
| Inlet Size | 1/2"-14 NPT | 1/2"-14 NPT | ||||||||
| Ports | 1 | 1 | 1 | |||||||
| Pressure Rating | 10-120 | |||||||||
| Configuration | Comes with gauge, gauge port is G 1/8. | |||||||||
| Advantages |
Eliminate Downtime-They Don’t Stick Normal air valves can stick or jam and cause start-up problems because of their inability to handle accumulations of dir, dust, oil or water in air lines. Not with the Ceram valve. There’s no gap between the plates for dirt and oil to accumulate. The plates are finished so precise that they act like sliding magnets or jo blocks. Solenoid operators of the same voltage on standard valves are interchangeable between all sizes, reducing spare parts inventory and downtime. They Work Great in Normal Applications Too Just because they are so popular in harsh environments, don’t think they won’t work great in a more normal application. Ceram Valves Save Air and Money The tight shut-off with Ceram valves eliminates costly loss of air that is common in other designs. Compressed air that you pay for. Extended Life Years of proven field service verifies an anticipated life of 150 million cycles even under adverse conditions. Overcomes Design Limitations of Other Valves Lapped spool valves normally have a small gap between spool and sleeve that is prone to oil and dirt accumulation, resulting in sticking and the waste of air. Packed spool valves using elastomer seals are subject to deterioration and excessive wear when contamination and/or incompatible lubricants are present. |
|||||||||
|
|
||||||||||
